matrix clearcoat msv 25 low voc quick with activator.

Description

Promotion sale for matrix clearcoat msv-25 quick cure with activator.
Best price in market. Cars are going to be done in 1.5 hours.
GENERAL INFORMATION MSV-25 Low VOC Quick Cure Clearcoat is designed for quick repairs over a wide temperature range in areas that require a 2.1 VOC Clearcoat. This product is intended for small, 1-2 panel size jobs. MSV-25 Low VOC Quick Cure Clearcoat can be polished, or delivered same day without baking.
1. COMPONENTS • MSV-25 Low VOC Quick Cure Urethane Clearcoat • MHV-25 Low VOC Quick Cure Clearcoat Hardener
2. MIXING RATIO (4:1) • Mix four (4) parts MSV-25 Low VOC Quick Cure Urethane Clearcoat with one (1) part of MHV-25 Low VOC Quick Cure Clearcoat Hardener.
3. POT LIFE @ 77°F (25°C) • Sprayable 30-60 minutes. *NOTE: Pot life will shorten as temperatures increase. Matrix System products are not recommended for use in temperatures below 65°F
4. CLEAN UP • Clean equipment immediately after use (check local regulations)
5. ADDITIVES • N/A
6. SURFACE PREPARATION FOR APPLICATION OVER RECOMMENDED BASECOAT SYSTEM ONLY • Allow basecoats sufficient dry times OEM BLEND AREAS Option 1: • Clean blend area with appropriate Matrix surface cleaner based on local regulatory compliance. • Scuff blend area with gray scuff pad and sanding paste • Sanding paste must be thoroughly washed away • Reclean blend area with Matrix surface cleaner prior to topcoating Option 2: • Clean blend area with appropriate Matrix surface cleaner based on local regulatory compliance • Sand blend areas with P800 - P1000 grit paper, for hard to reach areas scuff with gray scuff pad • Reclean blend area with Matrix surface cleaner prior to topcoating *NOTE: Option 1 and 2 the OEM Blend area must be scuffed or sanded completely dull
7. TOPCOATS • N/A
8. TECH NOTES • Matrix does not recommend nor warranty the blending of clear coats. Over reduction or solvent blending of the clear coat will become visible over time due to UV exposure on the blended edge. The edge may also fade or peel over time due to the minimal film thickness of the blended edge. • Matrix recommends applying clear coat to the entire panel. Many of today’s late model cars do not have a distinct edge or a break line on the quarter panel, in these cases Matrix recommends applying the clear coat to the roof and the opposite quarter panel. • This procedure will assure a professional repair, that returns the vehicle back to pre accident condition
9. SUBSTRATES • All Matrix Refinish Basecoats • Existing OEM Finishes
10. APPLICATION • Apply two (2) medium wet coats with 2-3 minutes flash between coats. *See Notes for additional information
11. FLASH / DRY TIMES AIR DRY @ 77°F (25°C) Flash (after 1st coat) 2-3 minutes Flash (after 2nd coat) N/A Out-of-Booth 15-30 minutes depending on temp Deliver/Polishing/Recoating 1.5 hours
12. SPRAY GUN SET UP HVLP/LVLP - Fluid Tip Size 1.3 mm - 1.4 mm AIR PRESSURES • Refer to spray gun manufacturer's recommendations for regulatory compliance
13. PHYSICAL DATA RTS REGULATORY DATA 4:1 LBS./GAL. g/L Actual VOC 0.93 111 Regulatory VOC (less water and exempt solvents) 2.08 249 Density 8.74 1047 WT.% VOL.% Total Solids Content 33.9 31.1 Total Volatile Content 66.2 68.9 Water 0 0 Exempt Compound Content 55.52 55.4 Coating Category Clearcoat *NOTE: US Regulations allow for the use of exempt compounds for VOC calculations.